Blogs Recent Entries Best Entries Best Blogs Blog List Search Blogs. Home My iTrader Join the NRA Donate to CGSSA Sponsors CGN Google Search. CA Semiauto Ban AW ID Flowchart CA Handgun Ban ID Flowchart CA Shotgun Ban ID Flowchart.

The dreams will come to you. Ricky-Ray View Public Profile Find all posts by Ricky-Ray. That is the machine nut in the foreend and the wood screw in the butt. I have 2 part epoxy if needed which I used on a Tapco T6 and it worked out..

Bladewurk View Public Profile Find all posts by Bladewurk. I drilled the stock per the instructions on the Uncle Mike's swivels, threaded the hole using the swivel bolt, removed the bolt, applied J-B Weld and reinstalled the bolt and swivel. Worked like a champ! VictorFranko View Public Profile Find all posts by VictorFranko. If the synthetic stock is mostly hollow and there is room inside, I prefer to use the the swivel stud type that uses a machine screw thread with a locknut and washer on the inside of the stock.

This is less likely to pull out than the wood screw thread type. If the synthetic stock is solid, the wood screw type is OK to use. Better yet, take a small piece of oak or other hardwood and rough it out so it will fit inside the cavities in the forearm and butt of the stock. I used a bench sander to finish fit the piece so it was flush with the bottom of the stock and did not interfere with the barrel which is free-floated.

RUGER ACCESSORIES

When the fit was perfect I epoxied the wood plugs in place and let them cure. Then get an Uncle Mikes wood stock kit and drill and tap into the synthetic stock with the hardwood backing and install the swivel studs as in a wood stock gun. The load is distributed over a much larger area than a single bolt.

10/22® Sling w/ Mag Pouch-ShopRuger

Diamondback68 View Public Profile Find all posts by Diamondback Does anyone know if Uncle Mikes has a 1. I have the standard Ruger hollow synthetic stock and I don't have the belt sander to try to use a wood insert. Also, how do you get the butt plate off?

I just realized there aren't any screws. Check out our parts kit locator that is automatically updated every 6 hours.

Now you can see parts kits being offered by multiple websites in one location. Just select the parts kit button on the right of the home page to begin looking. Originally Posted by straykiller. Originally Posted by andersoncouncil. So I got some Uncle Mike's studs to put on my synthetic. This may seem like a dumb question, but about where should I drill my holes? Thread Tools Show Printable Version. Display Modes Linear Mode Switch to Hybrid Mode Switch to Threaded Mode.

BB code is On. Forum Jump User Control Panel Private Messages Subscriptions Who's Online Search Forums Forums Home CALGUNS. All times are GMT The time now is 4: CA Semiauto Ban AW ID Flowchart.

CA Handgun Ban ID Flowchart. CA Shotgun Ban ID Flowchart.

Find all posts by pratchett. West Covina, CA Posts: Find all posts by Ricky-Ray. Find all posts by Bladewurk. Blade, where did you get the swivle kit? Find all posts by mcmski.

You can not protect the 1st Amendment without the 2nd Amendment Find all posts by VictorFranko. Find all posts by ojisan. Find all posts by Diamondback Find all posts by andersoncouncil. Find all posts by straykiller.

Ruger 44 Carbine stock help - ARCOM

Originally Posted by straykiller i have an OD Hogue overmold stock ill sell you for pretty cheep. Originally Posted by andersoncouncil I have the standard cheap barrel. Switch to Hybrid Mode. Switch to Threaded Mode. You may not post new threads You may not post replies You may not post attachments You may not edit your posts BB code is On Smilies are On [IMG] code is On HTML code is Off Forum Rules.